MotoWing Atölye
Motorcycle Calculators
Dişli değiştirmeden, zincir almadan ya da farklı ebatta lastik takmadan önce sonucu gör. Kendi motorunun değerlerini yaz, hesap anında güncellenir.
Dişli oranı hesaplama
Ön ve arka dişlinin diş sayısını yaz (dişlinin üzerinde 14T, 40T gibi yazar). Örnek değerler dolu, kendi değerlerinle değiştir.
İlgili: Zincir dişli seti kodları (428H, 520HO, 40T…) · Aktarma parçaları
Zincir boyu (bakla sayısı) hesaplama
Aks mesafesi: ön dişli merkezi ile arka aks merkezi arası, milimetre. Ölçerken arka aksı gergi ayarının ortasında tut.
İlgili: Zincir bakımı nasıl yapılır? · Zincir ve dişli setleri
Lastik ebatı hesaplama
Lastik yanağındaki ölçüyü yaz: 110/70-17 için genişlik 110, oran 70, jant 17. Ön ve arka lastiği ayrı hesapla.
Yakıt tüketimi hesaplama
Depoyu ağzına kadar doldur, günlük kilometreyi sıfırla; bir sonraki dolumda gidilen yolu ve aldığın litreyi yaz.
İlgili: Yakıt tüketimi neden artar? · Bakım Merkezi
Sonuçlar formüle dayalı tahminlerdir; üretim toleransı, lastik aşınması ve zincir esnemesi gerçek değeri biraz değiştirir. Motoruna özel parça için Garajım'dan motorunu seç ya da WhatsApp'tan sor.
How is it calculated?
Gear ratio
Final drive ratio = rear sprocket tooth count ÷ front sprocket tooth count. For example, a 40-tooth rear sprocket and a 14-tooth front sprocket give a ratio of 40 ÷ 14 = 2.86. Increasing the rear sprocket or decreasing the front sprocket shortens the ratio: acceleration becomes more agile, and the engine rotates at a higher RPM at the same speed. The opposite lengthens the ratio. Change in speed at the same RPM = old ratio ÷ new ratio.
Chain length (number of links)
Number of links ≈ 2 × wheelbase ÷ pitch + (front sprocket + rear sprocket) ÷ 2 + ((rear sprocket − front sprocket) ÷ 2π)² × pitch ÷ wheelbase. The pitch is 12.7 mm (1/2 inch) for 420 and 428 chains, and 15.875 mm (5/8 inch) for 520, 525, and 530 chains. The result is rounded up to the nearest even number; the "106L" expression in the product codes indicates 106 links. For the meaning of the codes, see the Chain Sprocket Set guide.
Tire size
Tire diameter (mm) = rim (inches) × 25.4 + 2 × width × aspect ratio ÷ 100. On a 110/70-17 tire, the sidewall height is 77 mm, and the total diameter is approximately 586 mm. If the diameter increases, the speedometer shows the actual speed lower than it is; if it decreases, it shows it higher. For reading the measurements and the DOT code, see the tire guide.
Fuel consumption
Consumption per 100 km = liters taken ÷ km traveled × 100. Fill the tank to the brim and reset the odometer, write down the distance and liters at the next fill-up; the average of 2–3 fill-ups gives the most accurate result. Why does consumption increase? 10 reasons and solutions.